Wear Mechanisms and Methods of Controlling the Wear Resistance of TiN/AlN Nanocomposite Coatings for Tribological Purpose

The aim of this work was to analyze the wear resistance of composite ion-plasma coatings and substantiate methodological approaches for its prediction. The object of the study was multilayer 2D-nanocomposite coatings of the TiN/AlN system with a total thickness of 0.8—4.0 μm. The coatings were applied using vacuum ion-plasma technology onto a substrate made of 40CrNiMo structural steel with a sorbite structure and a hardness of HRC 28—30. Within each nitride layer, the composition of the components was close to equiatomic, and for the coating as a whole it was Ti:Al:N = 1:1:2 (at. %). The structure of the coatings, the morphology of the friction tracks and the wear mechanisms were studied using high-resolution scanning electron microscopy. The mechanical characteristics of the coatings (hardness H and elastic modulus E) were determined using standard continuous indentation techniques. The tribological characteristics (friction coefficient m and volume wear J) were determined using the ball-on-disk sliding friction test with a circular trajectory of the indenter ball. The analysis of the obtained experimental data made it possible to construct a dependence of the coating hardness on their elemental composition and showed that the mechanical characteristics and wear resistance of the coatings sprayed at a lower temperature of 300—350 °C are consistently higher than those sprayed at 400—450 °C. In addition, it was found that the highest wear values ​​J were observed for the coatings with the smallest thickness. In order to analyze the effect of the coating thickness d on their wear resistance, a computational and analytical model for predicting coating wear during tribological tests was used. On its basis, diagrams of critical states of ion-plasma composite TiN/AlN coatings were constructed, which made it possible to calculate the critical value of the coating thickness d_min, at which the mechanism of coating wear during friction changes. With a relatively thin coating (d < d_min), located on a “softer” (plastic) substrate, during tribotesting, accelerated wear of the coating occurs by the abrasive-mechanical mechanism due to the deflection of the coating and its subsequent cracking, peeling and chipping. With a relatively thick coating (d ³ d_min), wear occurs by the abrasion mechanism, which, with high hardness of the coating, is characterized by its significant wear resistance and significantly extends the service life.

1. Myshkin N.K., Petrokovets M.I. Trenie, smazka, iznos. Fizicheskie osnovy` i inzhenerny`e prilozheniya tribologii. — M.: Fizmatlit. — 2007 (in Russian)

2. Belyi A.V., Karpenko G.D., Myshkin N.K. Struktu-ra i metody formirovaniya iznosostoykikh pov-erkhnostnykh sloyev. — M.: Mashinostroyeniye. — 1991 (in Russian)

3. Surface Engineering for Enhanced Performance against Wear / M. Roy (ed.). — Wien: Springer-Verlag. — 2013. https://doi.org/10.1007/978-3-7091-0101-8_2

4. Cavaleiro A. and De Hosson J.T. Nanostructure Coatings. — New York: Springer Science+Business Media, LLC. — 2006

5. Kolesnikov V.I., Kudryakov O.V., Voropaev A.I., Kolesnikov I.V., Varavka V.N., Lifar M.S., Guda A.A., Manturov D.S., and Novikov E.S. Formation and Prediction of Tribotechnical Proper-ties of Ion-Plasma Diamond-Like Coatings under Stabilization with Nitrogen // Journal of Friction and Wear. — 2024 (45), no. 1, 9—17. DOI: 10.3103/S1068366624700028

6. Il`in A.A., Plixunov V.V., Petrov L.M., Spek-tor V.S. Vakuumnaya ionno-plazmennaya obra-bot¬ka. — M.: Al`fa-M:INFRA-M. — 2023 (in Rus-sian)

7. Pogrebnyak A.D., Komarov F.F., Beresnev V.M., Konstantinov S.V., Salishhev G.A. Mnogokompo-nentny`e i vy`sokoe`ntropijny`e splavy` i nitridny`e pokry`tiya na ix osnove. — M.: LENAND. — 2021 (in Russian)

8. Krishtal M.M., Yasnikov I.S., Polunin V.I., Fila-tov A.M., Ul`yanenkov A.G. Skaniruyushhaya el-ektronnaya mikroskopiya i rentgenospektral`ny`j mikro¬analiz v primerax prakticheskogo primeneni-ya / Pod red. M.M. Krishtala. — M.: Texnosfera. — 2009 (in Russian)

9. Golovin Yu.I. Nanoindentirovanie i ego vozmozh-nosti. — M.: Mashinostroenie. — 2009 (in Russian)

10. GOST 8.748-2011 (ISO 14577-1:2002). Metally` i splavy`. Izmerenie tverdosti i drugix xarakteris-tik materialov pri instrumental`nom indentiro-vanii. Chast` 1: Metod ispy`tanij. (in Russian)

11. GOST R 50779.25-2005 (ISO 3494:1976). Statis-ticheskie metody`. Statisticheskoe predstavlenie danny`x. Moshhnost` testov dlya srednix i dis-persij. (in Russian)

12. GOST R ISO 16269-4-2017. Statisticheskie meto-dy`. Statisticheskoe predstavlenie danny`h. Chast` 4: Vy`yavlenie i obrabotka vy`brosov. (in Rus-sian)

13. Kudryakov O.V., Kolesnikov V.I., Kava¬liova I.N., Kolesnikov I.V., and Manturov D.S. Calculation and Analytical Prediction of Coating Wear During Tribological Tests Based on Models of Contact Fa-tigue Failure. Part 2 // Journal of Friction and Wear. — 2024 (45), no. 3, 179—187. DOI: 10.3103/S1068366624700272

14. Kolesnikov Yu.V., Morozov E.M. Mexanika kon-taktnogo razrusheniya. — M.: Izdatel`stvo LKI. — 2007 (in Russian)