Comprehensive Study of the Single High-Energy Laser Pulse Effect on the Wear Resistance of R6M5 Steel

The researches of microstructure changes and structural defects (using the example of dislocation density) of samples made of high-speed steel R6M5 and irradiated with a single high-energy laser pulse as well as the effect of these changes on the abrasive wear resistance of the studied material are presented in the article. It was found that the proposed laser treatment significantly affects the microstructure of the irradiated samples. This is expressed in the almost complete disappearance of the banded distribution of carbides in the samples, which indicates a partial redistribution and dissolution of “heavy” carbides of the Me6C type containing tungsten and molybdenum in the material matrix (martensite). In this case, the configuration of “heavy” Me6C carbides is located between the formulas Fe3(W,Mo)3C – Fe4(W,Mo)2C. Also, exposure to a high-energy laser pulse leads to an increase in the quantity and size of secondary carbides in the alloy matrix, significantly enriched in tungsten and molybdenum. In addition, there is a change in the type of vanadium carbides from Me2C to VC, accompanied by a significant decrease in the amount of molybdenum and tungsten in it. Using the Thixomet image analysis program, it was determined that the number of grains of “heavy” Me6C carbides in terms of volume decreased by 1.30—1.58 times, depending on the distance from the point of interest to the irradiation place of the sample. At the same time, the average size and direction (anisotropy) of the material grains has not changed. The results of X-ray phase analysis showed that after treatment, the number of main phases of the samples remained practically unchanged in distribution, but there was an increase in the responses intensity. Based on the above, the change in the structure defectiveness was determined using the example of dislocation density. The results of abrasive wear tests showed that there is an increase in the wear resistance of irradiated samples by 1.58—2.48 times, depending on the distance from the point of interest to the irradiation place of the sample. In this case, the value of the greatest wear resistance (2.48 times) is achieved with the greatest microstructure changes and structure defectiveness, which corresponds to the distance from the point of interest to the irradiation place of the sample equal to 20 millimeters. The obtained results allow us to recommend the use of the microstructural analysis method for assigning optimal modes of laser hardening of materials.

1. Pinahin I.A., Sharma S.K., Yagmurov M., Vrublevskaya S., and Shpack M. Correlation between Wear Resistance of High-Speed Steel R6M5 and Deformations Arising during Laser Hardening // Journal of Friction and Wear. — 2023 (44), no. 2, 158—166

2. Zhao К., Yan G., Li J., Guo W., Gu J., and Li С. The Resistance to Wear and Thermal Cracking of Laser Surface Engineered P20 Steel // Coatings. — 2023 (13), no. 1, 97

3. Moiseyev V. F., Grigor'yev S. N. Instrumental'nyye materialy. — Moskva: MGTU “Stankin” (OOO Inform-Soft). — 2005 (in Russian)

4. Skakov M.K., Rakhadilov B.K., and Sheffler M. Modification of Structure and Properties of Steel R6M5 at Electrolyte Plasma Treatment // Advanced Materials Research. — 2013 (601), 64—68

5. Ke R., Hu C., Zhong M., Wan X., and Wu K. Grain Refinement Strengthening Mechanism of an Austenitic Stainless Steel: Critically Analyze the Impacts of Grain Interior and Grain Boundary // J. Mater. Res. Technol. — 2022, no. 17, 2999—3012

6. Rezayat M., Moradi M., and Mateo A. Nanosecond Pulsed Laser Surface Processing of AISI 301LN Steel: Effect on Surface Topography and Mechanical Properties // Int. J. Adv. Manuf. Technol. — 2023, no. 128, 3025—3040

7. Soliс S., Cajner F., and Leskovsek V. Effect of Deep Cryogenic Treatment on Mechanical and Tribological Properties of PM S390 MC High-Speed Steel // MP Materials Testing. — 2012, no. 10, 688—693

8. Kremnev L.S. Theory of alloying and the creation of heat-resistant tool steels and alloys on its basis // Metal science and heat treatment of metals (MiTOM). — Moscow. — 2008, no. 11(641), 18—27 (in Russian)

9. Pinakhin I.A., Chernigovsky V.A., Bratsikhin A.A., Yagmurov M.A., and Vladykina Yu.A. Improving Wear Resistance of Fast-Cutting Steel R6M5 after a Volume Pulse Laser Strength // Journal of Friction and Wear. — 2019 (40), no. 3, 304—309

10. Kozlov E.V., Ivanov Yu.F., Simonov P.S. and others. Phase composition and fine structure of R6M5 steel // Polzunovsky almanac. — 2004, no. 4, 47— 51 (in Russian)

11. Kumar V., Verma R., Kango S., and Sharma V.S. Recent Progresses and Applications in Laser-Based Surface Texturing Systems // Mater. Today Commun. — 2021, no. 26, 101736

12. Pinahin I.A., Shagrov M.N., Yagmurov М.A., Vrublevskaya S.S., Darzhaniya A.Yu., and Shpak M.A. Wear Resistance Increase of SingleCarbide Hard Alloys after Bulk Pulse-Laser Hardening // Journal of Friction and Wear. — 2020 (41), no. 6, 554—558

13. Rezayat M., Roa J.J., and Mateo A. Effect of Laser Surface Texturing on Schmid Factor and Plastic Deformation Mechanisms on AISI 301LN Steel // Metals. — 2023, no. 13, 1789

14. Cordovilla F., García-Beltrán Á., Dominguez J., Sancho P., and Ocaña J.L. Numerical-Experimental Analysis of the Effect of Surface Oxidation on the Laser Transformation Hardening of Cr–Mo Steels // Appl. Surf. Sci. — 2015, no. 357, 1236— 1243

15. Mohamed H., Ataiwi A., and Dawood J. Mechanical Properties of Martensitic Stainless Steel (AISI420) Subjected to Conventional and Cryogenic Treatments // Eng. Technol. J. — 2020, no. 38, 1096—1105